Holder metallic red
54,99 € Couple
t-blade Holder Metallic Red
The t-blade Holder Metallic Red is an special optical design of the proven t-blade ski system. Construction, geometry, stiffness and system compatibility correspond. completely the standard black version.
Technical Basis & System Architecture
The t-blade Holder forms the central connection between ice skating boot and Runner and is consistently focused Maximum stability, precise power transmission and high operational reliability designed.
Made of cold-impact resistant, fiber-reinforced plasticthe Holder -25 °C shatterproof and designed for continuous use in ice hockey.
The continuous, bridge-like construction from the Holderfront to HolderHeck forms together with integrated transverse ribs a pronounced force triangleThis allows the Holder a very high Torsional, longitudinal and transverse stability.
Construction & Stability
The continuous, bridge-like construction from the Holderfront to HolderHeck forms together with integrated transverse ribs a pronounced force triangleThis construction method ensures:
- very high Torsional stability
- maximale Longitudinal and transverse force absorption
- a noticeable direct power transmission without energy loss
The design-related stiffness of the HolderIt stabilizes the Sustainable ice skate sole and reduced axial bending forces in the central area of the ice skating boot.
Geometry & Handling
The defined, closed Holder-Explosive supports the optimal knee and forward lean angles of the runner system. This improves control over the skate and enables efficient power transfer when accelerating and turning.
Runner-Recording & Stabilisatoren
The trapezoidal connection between Runner and Holder guarantees one play-free, perfectly fitting seatThis allows for high Acceleration and lateral forces be transmitted securely.
For assembling the Stabilisatoren are on the Holder-Inside precise recesses at the screw points integrated. These enable a flat, stable construction the locking washers.
Incorrect assembly inevitably leads to loss of stability and increased wear of the plastic locking washers.
Mounting on the ice skate
The im Holder-Fixing holes inserted around the sole edge allow flexible positioning and fastening of the Holders on the sole of the ice skate:
- Fastening via rivet
- or by RMS screw connection
In the rear area of the Holders is located Contour opening for the clip-in t-blade logo clip.
Note: The Holder reaches his Maximum rigidity and operational reliability are achieved exclusively through the combination of all t-blade system components..
Advantages at a glance
- Extremely high stability due to Force triangle construction
- Very high Transverse and longitudinal force stability
- closed construction between front and rear areas
- Sustainable Improvement of ice skate sole stiffness
- Cold impact resistant and shatterproof down to -25 °C
- Tried and tested Multi-hole and bridge design
System sizes
Standard system sizes:
248 · 256 · 264 · 272 · 280 · 288 · 300 mm
Image note:
Holder with System length 248 mm have 4 cutouts, away 256 mm it is 5 cutouts.
Lindauer Str. 1a
86842 TürkheimResponsible person: support@t-blade.shopWarnings and safety information:
Warnings & Safety Information
T-Blade The products are sporting goods for use in ice hockey, figure skating and similar sports.
Ice sports. Use is entirely at your own risk.
-
Risk of injury: runners, Runner And interchangeable blades are sharp. In case of improper use
Handling poses a risk of cuts and injuries. -
Assembly & Replacement: The exchange of Runnern, stubbies or other system components
Installation must be carried out only according to the manufacturer's instructions. Improper installation can lead to material failure and loss of control.
or lead to injuries. -
Regular controll: Before each use, all fasteners, screws and system parts must be checked.
to check for secure fit, wear and damage. -
Wear parts: Runner and replaceable blades are subject to natural wear and tear and must be replaced when necessary.
Wear and tear should be replaced in a timely manner. -
Protective gear: Wearing appropriate protective equipment (e.g. helmet, pads) is strongly recommended.
empfohlen. -
Not for children without supervision: Use by children should only be under supervision and
Instructions will follow. -
Not a toy: T-Blade These products are not toys and are not intended for improper use.
Intended use.
The manufacturer and distributor accept no liability for damages or injuries caused by improper use.
These problems can arise from improper use, incorrect assembly, or lack of maintenance.
All color variations of the t-blade Holders They are technically identical. The choice of color is purely aesthetic.
t-blade Holder-Size finder: Shoe size → t-blade system size
For ordering the t-blade Holders It's not the shoe model that's crucial, but the right one.
t-blade system size (HolderLength). Find your brand and size in the table and order the specified system size.
The information CM is just a check: it corresponds to the Foot length in centimeters.
Important: FARMER and CCM have here the identical Assignment. GRAF uses its own mapping.
BAUER & CCM – Assignment to t-blade system size
| Bauer / CCM Size | Shoe sizes | t-blade system size | |||
|---|---|---|---|---|---|
| US | EU | UK | cm (foot length) | ||
| 5 | 6 | 38,5 | 5,5 | 24,3 | 248 |
| 5,5 | 6,5 | 39 | 6 | 24,7 | 248 |
| 6 | 7,5 | 40,5 | 6,5 | 25,1 | 248 |
| 6,5 | 8 | 41 | 7 | 25,5 | 256 |
| 7 | 8,5 | 42 | 7,5 | 26 | 256 |
| 7,5 | 9 | 42,5 | 8 | 26,4 | 264 |
| 8 | 9,5 | 43 | 8,5 | 26,8 | 264 |
| 8,5 | 10 | 44 | 9 | 27,2 | 272 |
| 9 | 10,5 | 44,5 | 9,5 | 27,7 | 272 |
| 9,5 | 11 | 45 | 10 | 28,1 | 280 |
| 10 | 11,5 | 45,5 | 10,5 | 28,5 | 280 |
| 10,5 | 12 | 46 | 11 | 28,9 | 288 |
| 11 | 12,5 | 47 | 11,5 | 29,4 | 288 |
| 11,5 | 13 | 47,5 | 12 | 29,8 | 300 |
| 12 | 13,5 | 48 | 12,5 | 30,2 | 300 |
GRAF – Assignment to t-blade system size
| Shoe sizes | t-blade system size | |||
|---|---|---|---|---|
| US | EU | UK | cm (foot length) | |
| 5,5 | 37 1/3 | 4,5 | 23,5 | 248 |
| 6 | 38 | 5 | 24 | 248 |
| 6,5 | 38 2/3 | 5,5 | 24,5 | 248 |
| 7 | 39 1/3 | 6 | 25 | 248 |
| 7,5 | 40 | 6,5 | 25,3 | 256 |
| 8 | 40 2/3 | 7 | 25,7 | 256 |
| 8,5 | 41 1/3 | 7,5 | 26 | 264 |
| 9 | 42 | 8 | 26,5 | 264 |
| 9,5 | 42 2/3 | 8,5 | 27 | 272 |
| 10 | 43 1/3 | 9 | 27,5 | 272 |
| 10,5 | 44 | 9,5 | 28 | 280 |
| 11 | 44 2/3 | 10 | 28,3 | 288 |
| 11,5 | 45 1/3 | 10,5 | 28,5 | 288 |
| 12 | 46 | 11 | 29 | 288 |
| 12,5 | 46 2/3 | 11,5 | 29,5 | 300 |
| 13 | 47 1/3 | 12 | 30,0 | 300 |
BAUER & CCM – Assignment to t-blade system size
GRAF – Assignment to t-blade system size
Discover More
Holder metallic blue
55,00 € Couple
Holder metallic chrome
55,00 € Couple
Holder metallic gold
55,00 € Couple
Holder painted pink
49,00 € Couple
Reviews
Clear FiltersThere are no reviews yet.