Holder black
39,00 € Couple
t-blade Holder Black – stable base of the t-blade runner system for secure grip on the ice
The t-blade Holder Black is the load-bearing base element of the t-blade skid system and connects the ice skating boot directly to the t-blade Runnern. It forms the constructive basis for Stability, control and secure footing on the ice.
The t-blade system is not exclusively for ice hockey players designed. It is particularly suitable for Beginners and ambitious recreational drivers, because the skid system, due to its design, always allows stable, predictable stand and uniform power transmission enables. At the same time, the Holder also the requirements of sport-oriented drivers.
The Holder It achieves its full performance only when used in conjunction with all original t-blade system components.
Material & Durability
The t-blade Holder consists cold-impact resistant, fiber-reinforced high-performance plastic.
He is up to -25 °C shatterproof and designed for continuous use on the ice – both in recreational and sporting settings.
Construction & Stability
The continuous, bridge-like construction of Holderfront to HolderThe rear section, together with integrated transverse ribs, forms a pronounced force triangleThis construction method ensures:
- very high torsional stability
- safe absorption of longitudinal and transverse forces
- direct power transmission without unstable yielding
The inherent rigidity of the design sustainably stabilizes the skate sole and reduces axial bending forces in the central area of the skate boot. The result is a smooth, controlled driving experience, which offers additional safety, especially for beginners.
Geometry & Handling
The defined, closed Holder-Explosive This supports a natural stance and a stable angle of the runner system. This results in:
- the grip on the ice is improved
- the balance is facilitated
- increases control during changes of direction
Especially for beginners and ambitious recreational cyclists, this contributes to a safe, confidence-building driving behavior at.
Runner-Recording & Stabilisatoren
The trapezoidal Runner-Recording ensures a play-free, precise fit between Holder and RunnerThis allows for performance even under higher loads. Reliably transmit curve and lateral forces .
On the inside of the Holders are precise recesses at the screw points for the Stabilisatoren integrated. These ensure a flat, stable installation of the locking washers.
Note:
A faulty assembly of the StabilisatorThis inevitably leads to a loss of stability and increased wear of the plastic locking washers.
Mounting on the ice skate
The integrated mounting holes around the edge of the sole allow for flexible and secure installation of the Holders on the sole of the ice skate:
- Fastening via rivets
- or via RMS screw connection
The contour opening for the clip-in component is located at the rear. t-blade logo clip.
System notice
The t-blade Holder is a System componentMaximum stability, safety, and performance are ensured. only when used in conjunction with all original t-blade components The system has been achieved. Using individual components outside the system is not recommended.
Advantages at a glance
- Very high grip and stability on the ice
- Ideal for beginners and ambitious recreational riders
- Calm, controlled driving behavior
- High torsional and lateral force stability
- Closed, continuous construction
- Cold impact resistant and shatterproof down to -25 °C
- Proven multi-hole and bridge design
System sizes
Standard system lengths:
248 · 256 · 264 · 272 · 280 · 288 · 300 mm
Image note:
Holder With a system length of 248 mm, there are 4 recesses; from 256 mm there are 5 recesses.
Delivery
- 1 pair of t-blades Holder (left + right)
- Delivery without Runner, Stabilisatoren, clips and fastening material
Compatibility
- Exclusively compatible with original t-blade system components
- Not compatible with classic ice skatesHoldern other manufacturer
Assembly instructions
The assembly should only be carried out by personnel respectively.
Improper installation can lead to loss of function and safety risks.
| Color | Black |
|---|---|
| Mounting | Rivets · RMS screw connection |
| Temperature resistance | Down to -25 °C |
| Material | Fiber-reinforced high-performance plastic |
| System length (mm) | 248, 256, 264, 272, 280, 288, 300 |
| Compatibility | T-blade system only |
| field of application. | Beginners · Recreational drivers · Sport-oriented drivers |
| Quantity | Pair (left & right) |
| Component | Holder |
| System | t-blade skid system |
| Product type | t-blade system component |
Lindauer Str. 1a
86842 TürkheimResponsible person: support@t-blade.shopWarnings and safety information:
Warnings & Safety Information
T-Blade The products are sporting goods for use in ice hockey, figure skating and similar sports.
Ice sports. Use is entirely at your own risk.
- Risk of injury: runners, Runner And interchangeable blades are sharp. In case of improper use
Handling poses a risk of cuts and injuries. - Assembly & Replacement: The exchange of Runnern, stubbies or other system components
Installation must be carried out only according to the manufacturer's instructions. Improper installation can lead to material failure and loss of control.
or lead to injuries. - Regular controll: Before each use, all fasteners, screws and system parts must be checked.
to check for secure fit, wear and damage. - Wear parts: Runner and replaceable blades are subject to natural wear and tear and must be replaced when necessary.
Wear and tear should be replaced in a timely manner. - Protective gear: Wearing appropriate protective equipment (e.g. helmet, pads) is strongly recommended.
empfohlen. - Not for children without supervision: Use by children should only be under supervision and
Instructions will follow. - Not a toy: T-Blade These products are not toys and are not intended for improper use.
Intended use.
The manufacturer and distributor accept no liability for damages or injuries caused by improper use.
These problems can arise from improper use, incorrect assembly, or lack of maintenance.
All color variations of the t-blade Holders They are technically identical. The choice of color is purely aesthetic.
t-blade Holder-Size finder: Shoe size → t-blade system size
For ordering the t-blade Holders It's not the shoe model that's crucial, but the right one.
t-blade system size (HolderLength). Find your brand and size in the table and order the specified system size.
The information CM is just a check: it corresponds to the Foot length in centimeters.
Important: FARMER and CCM have here the identical Assignment. GRAF uses its own mapping.
BAUER & CCM – Assignment to t-blade system size
| Bauer / CCM Size | Shoe sizes | t-blade system size | |||
|---|---|---|---|---|---|
| US | EU | UK | cm (foot length) | ||
| 5 | 6 | 38,5 | 5,5 | 24,3 | 248 |
| 5,5 | 6,5 | 39 | 6 | 24,7 | 248 |
| 6 | 7,5 | 40,5 | 6,5 | 25,1 | 248 |
| 6,5 | 8 | 41 | 7 | 25,5 | 256 |
| 7 | 8,5 | 42 | 7,5 | 26 | 256 |
| 7,5 | 9 | 42,5 | 8 | 26,4 | 264 |
| 8 | 9,5 | 43 | 8,5 | 26,8 | 264 |
| 8,5 | 10 | 44 | 9 | 27,2 | 272 |
| 9 | 10,5 | 44,5 | 9,5 | 27,7 | 272 |
| 9,5 | 11 | 45 | 10 | 28,1 | 280 |
| 10 | 11,5 | 45,5 | 10,5 | 28,5 | 280 |
| 10,5 | 12 | 46 | 11 | 28,9 | 288 |
| 11 | 12,5 | 47 | 11,5 | 29,4 | 288 |
| 11,5 | 13 | 47,5 | 12 | 29,8 | 300 |
| 12 | 13,5 | 48 | 12,5 | 30,2 | 300 |
GRAF – Assignment to t-blade system size
| Shoe sizes | t-blade system size | |||
|---|---|---|---|---|
| US | EU | UK | cm (foot length) | |
| 5,5 | 37 1/3 | 4,5 | 23,5 | 248 |
| 6 | 38 | 5 | 24 | 248 |
| 6,5 | 38 2/3 | 5,5 | 24,5 | 248 |
| 7 | 39 1/3 | 6 | 25 | 248 |
| 7,5 | 40 | 6,5 | 25,3 | 256 |
| 8 | 40 2/3 | 7 | 25,7 | 256 |
| 8,5 | 41 1/3 | 7,5 | 26 | 264 |
| 9 | 42 | 8 | 26,5 | 264 |
| 9,5 | 42 2/3 | 8,5 | 27 | 272 |
| 10 | 43 1/3 | 9 | 27,5 | 272 |
| 10,5 | 44 | 9,5 | 28 | 280 |
| 11 | 44 2/3 | 10 | 28,3 | 288 |
| 11,5 | 45 1/3 | 10,5 | 28,5 | 288 |
| 12 | 46 | 11 | 29 | 288 |
| 12,5 | 46 2/3 | 11,5 | 29,5 | 300 |
| 13 | 47 1/3 | 12 | 30,0 | 300 |
BAUER & CCM – Assignment to t-blade system size
GRAF – Assignment to t-blade system size
Discover More
Holder metallic blue
55,00 € Couple
Holder metallic chrome
55,00 € Couple
Holder metallic gold
55,00 € Couple
Holder metallic red
54,99 € Couple
Holder painted pink
49,00 € Couple
Stabilisator with stainless steel screw fitting, black
38,00 € Couple
Reviews
Clear FiltersThere are no reviews yet.